When was the last time you had your (life support) Regulator and/or BCD serviced, per manufactuer's requirement? if you are not sure, have your life support systems serviced immediately for its annual service before your next diving adventure.
Our state of the art Service and Repair Department offers the highest quality diagnostic and repair equipment available.
Our Service and Repair manufacturer-trained Master Technican Tony Wiley or one of our other highly skilled manufacturer-trained technicians will deliver the most efficient and quality equipment service and repair.
Standard regulator and BCD service is 10 business days.
$50 Rush regulator and BCD service is 5 business days.
Winter Pricing:
Service your Regulator, BCD and Dive Computer(s) when you are not diving during the off-season.
Save 20% during the off-season (December thru February). Make sure your gear is here before the last week of February to take advantage of the savings.
Major overhaul Service which inlcludes disassembly, cleaning, and replacement of all seats and seals is recommended either annually or per manufactures requirement. We do require that you perform preventive maintenance (fresh water rinsing) as outlined in the manufactures user manual.
You should also bring the regulator into Riverside Scuba for an Annual Safety Inspection to check for proper funictioning. We will advise you of any problems that might necessitate an earlier than scheduled servicing.
REGULATOR INSPECTION
- External Inspection
- Check regulator system for signs of corrosion
- Check hoses and fittings for signs of ware and dyr rot
- 1st stage
- Inspect filter for signs of flooded or contamination
- Check the IP to ensure it is stable and within acceptable range.
- 2nd stage
- Check mouthpiece
- Check purge cover
- Check exhaust valves
- Check operation of adjustment knobs and venturi switches
- Check cracking effort and flow rate are within manufactures ranges
REGULATOR ANNUAL SERVICE & PRICES
- Pre-service check to help troubleshooting later in the service.
- Disassembly of the 1st stage, 2nd stage and gauges.
- Clean metal parts in an ultrasonic cleaner.
- Soak and scrub plastic parts in warm soapy filtered detilled water.
- Inspect all the parts for excessive wear, cracks, and corrosion.
- Replace all the manufacture required parts i.e. o-rings, filters, and seats.
- Reassemble the regulator.
- Adjust the regulators intermediate pressure, flow rate, and breathing resistance according to the manufactures specifications.
- Submerge regulator in water to ensure proper function.
COST PER ITEM
$40 Regulator 1st Stage Technician Labor. Parts Not Included.
$40 Regulator 2nd Stage Technician Labor. Parts Not Included.
$40 Octopus Only (Standard) Technician Labor. Note: If it is “Free-Flowing” it may be your regulators First Stage causing the leak. Bring in your entire (1st & 2nd stage) Regulator System. Parts not included.
$55 Octopus Only (Integrated) Serves as both Inflator & Octopus ( Atomic SS1, Scubapro’s Air Source 2, Gemini etc). Note: If it is “Free-Flowing” it may be your regulators First Stage causing the leak. Bring in your entire (1st & 2nd) stage Regulator System. Technician Labor. Parts not Included.
$35 1st Stage Full Service Parts Kit.
$29 2nd Stage Full Service Parts Kit.
$27 Atomic SS1, Gemini Octo, Scuba Pro Air2 etc.) Only. Full Service Parts Kit.
$20 Computer Service Replacement Battery & O-Ring Kit, Includes Labor.
$65 Spare Air / XTR Pony System Technician Labor. Does not include parts. -Any Spare Air Regulator (Regulator Portion Only) or Any XTR / Pony System Service (Regulator Portion Only). Does not include Tank VIP or Hydro.
$12 Burst Disc Technician Labor.
$15 Cylinder Valve Rebuild Service Technician Labor.
OTS FULL FACE MASK SERVICE & REPAIR RATES
Riverside Scuba is the OTS authorized Guardian Service and Repair Center. Our technicians were trained by Ocean Technogoly Systems (OTS) how to properly service OTS equipment by breaking down the Full Face Mask, breaking down the 2nd Stage Regulator, reinstalling components of the Full Face Mask, reinstalling the components of the 2nd Stage Regulator and proper adjustments of the 2nd Stage Regulator, to trouble shoot, service and repair your OTS products.
Obtaining service for your out of warranty or in-warranty OTS products is simple. You can either call us directly at 951-682-3483 or online. Please note that OTS uses a Flat Rate system. Refer to the chart below for our Flat Rate prices. Once you have received your RMA #, securely package the unit and ship it to:
Riverside Scuba
Attn: Service Department - RMA #
1043 West LA Cadena Drive
Riverside, CA 92501
MODEL | EVALUATION | FLAT RATE | |
Full Face Masks | |||
OTS Guardian FFM | ANNUAL MAINTENANCE | $250 | |
OTS Guardian FFM | MASK ONLY SERVICE | $105 | |
OTS Guardian FFM | LENS / VISOR REPLACMENT WITH ABV | $175 | |
OTS Guardian FFM | LENS / VISOR REPLACMENT | $70 | |
OTS Guardian FFM | SKIRT REPLACEMENT | $355 | |
OTS Guardian FFM | COLOR CHANGE (SKIRT NOT INCLUDED) | $139 | |
OTS Stealth FFM | ANNUAL MAINTENANCE | $250 | |
Interspiro AGA FFM | ANNUAL MAINTENANCE | $150 | |
Interspiro AGA FFM | 6 YEAR SERVICE | $265 | |
Interspiro AGA FFM | ANNUAL W/ AIR HATCH | $250 | |
Interspiro AGA FFM | AIR HATCH SERVICE | $110 | |
Interspiro AGA FFM | VISOR ONLY NO ABV OR HOLE (INTERSPIRO VERSION) | $110 | |
Interspiro AGA FFM | VISOR REPLACMENT WITH ABV (INTERSPIRO VERSION) | $269 | |
Interspiro AGA FFM | SKIRT REPLACEMENT | $510 | |
OTS Spectrum FFM | Lens Change | Lens Cost : Coated Lens $80, Clear Lens $50 | ||
OTS Spectrum FFM | SKIRT REPLACEMENT | $355 | |
Earphone/Microphone Assemblies | |||
Standard EM’s | EAR ELEMENT & COVERS (EACH) | $120 | |
Older Style (EP2) | EAR REPLACEMENT W/ POTTING SLEEVE | $175 | |
AGA Plate C-Clips | $40 | ||
AGA, OTS Mic Wires | $150 | ||
AGA Bushings | $70 | ||
AGA / OTS PTT Button | $65 | ||
AGA Plate Re-Glue | $65 | ||
Hot Mic Replacement | $185 | ||
Military EM’s | FLAT RATE | $310 | |
Diver Units (Includes Buddyphones, SSB Units, Etc.) | |||
Military Units | Battery Spring Contacts | $135 | |
Military Units | Vox, Squelch, Pots | $235 | |
Diver Units (Feed Through Cable/Ear) | Flat Rate | $260 | |
Diver Units (SSB-2010, 10001B / MAG-1003D) | Minor Maintenance Rate (Replacing Battery Rings, Battery Holders, O-Rings, PTT button only, Battery Snaps, and Stickers) |
$70 | |
Diver Units (SSB-2010, 10001B) | BELT CLIP | $65 | |
Diver Units (SSB-2010, 10001B) | FEED THROUGH CABLE | $275 | |
Diver Units (SSB-2010, 10001B) | HI-USE CONNECTOR | $175 | |
Diver Units (SSB-2010, 10001B) | GR-2 | $65 | |
Diver Units (SW-1000-SC / MAG’S) | Minor Maintenance Rate | $105 | |
MK-7 | MINOR MAINTENANCE (OLD) | $105 | |
MK-7 | MINOR MAINTENANCE (NEW) | $105 | |
BUDDY PHONE (NO BLUE / YELLOW) | MINOR MAINTENANCE | $85 | |
BUDDY PHONE (NO BLUE / YELLOW) | EAR REPLACEMENT | $270 | |
BUDDY PHONE (NO BLUE / YELLOW) | PTT ASSEMBLY | $345 | |
YELLOW / BLUE BUDDYPHONES | NO LONGER SERVICE | N/A | |
Surface Units | |||
BELL-100 | NO LONGER SERVICE | N/A | |
BELL-200 | FLAT RATE | $460 | |
BELL-200 | PCB REPLACEMENT | $1,485 | |
COMBOX | FLAT RATE | $230 | |
COMBOX | PCB REPLACEMENT (913144-900) | $505 | |
COMBOX-1 | NO LONGER SERVICE | N/A | |
DRS-100B | FLAT RATE (DOES NOT INCLUDE LL-98 SPEAKER) | $435 | |
DRS-100B | PCB REPLACEMENT | $1,530 | |
I-COM BOARD | FLAT RATE | $1,975 | |
LL-98 | FACTORY REBUILD | $810 | |
MAG-1001S | FLAT RATE | $510 | |
MAG-1001S | PCB REPLACEMENT | $2,685 | |
MK1-DCI | NO LONGER SERVICE | N/A | |
MK2-DCI: Connectors / Switches | 1/2 FLAT RATE | $210 | |
MK2-DCI: Troubleshoot / Components Failure | FLAT RATE | $410 | |
MK2-DCI | PCB REPLACEMENT | $1,025 | |
MK-III 3 DIVER | FLAT RATE | $510 | |
MK-III 3 DIVER | PCBA | $1,145 | |
MK-III 3 DIVER | CASE REPLACEMENT | $505 | |
MK-IV | FLAT RATE | $1,010 | |
MK-7 | FLAT RATE | $260 | |
MK-7 | AMP CONNECTORS | $195 | |
MK-7 | PCBA REPLACEMENT, ONLY. ADD’L $44.99 FOR PART | $85 | |
MK-7 | PCBA-MK7 | $605 | |
RCL-7A | FLAT RATE | $440 | |
SP-100 | NO LONGER SERVICE | N/A | |
SP-100D & D-2 | FLAT RATE | $365 | |
SP-100D & D-2 | PCB REPLACEMENT | $510 | |
SSB-1000S | NO LONGER SERVICE | N/A | |
STX-100 | NO LONGER SERVICE | N/A | |
STX-101 | FLAT RATE | $535 | |
STX-101 | PCB REPLACEMENT | $1,210 | |
STX-101 | CASE REPLACEMENT | $460 | |
STX-101M | FLAT RATE | $535 | |
STX-101M | PCB REPLACEMENT | $1,510 | |
STX-101SB | FLAT RATE | $560 | |
STX-101SB | PCB REPLACEMENT | $1,810 | |
MK3-KMDSI | FLAT RATE | $410 | |
MK3-KMDSI | PCB REPLACEMENT | $710 | |
DRS / MK-2 / ST-101 | LATCH REPLACEMENT ON CASE | $98 | |
ALL OTHER SURFACE STATIONS | CALL FOR QUOTE | ||
Headsets/Connectors | |||
HEADSETS / CONNECTORS / OTHER | HEADSET | COMROPE / TCA | EM |
HEADSETS (Electret no longer service) | $235 | N/A | N/A |
WINDSOCK | $25 | N/A | N/A |
Hi-USE CONNECTOR | $225 | $150 | $160 |
AMP CONNECTOR | $185 | $135 | SPECIAL |
MS CONNECTOR | $135 | $165 | SPECIAL |
DOUBLE BANANA | $105 | $50 | N/A |
MARSH MARINE | N/A | N/A | $160 |
POTTING SLEEVE | N/A | $100 | $160 |
Accessories | |||
SWIVEL | OK-S SERVICE | $65 | |
SWIVEL | OK-S-V2 SERVICE | $75 | |
GAS BLOCK | SERVICE | $65 | |
**ALL FLAT RATES EXCLUDE BATTERIES, TRANSDUCERS, PCA BOARD REPLACEMENTS AND ACCESSORIES** | |||
A $40-130 evaluation fee will be charged to test and evaluate equipment. |
BCD SERVICE & COST
The following is the procedures:
(01) Inspect Bladder Manufacture Date.
(02) Inspect Bladder Condition.
(03) Bladder Inflation Test.
(04) Bladder Submersion in Water Test.
(05) Inspect Dump Valves.
(06) Inspect Inflator/Deflator Hose and Assembly.
(07) Inspect, Disassemble and Clean Power Inflator.
COST PER ITEM
$30 BCD with Standard Power Inflator Technician Labor. Parts Not Included.
$55 BCD with Alternate Octo/Inflator (Atomic SS1, Gemini Octo, Scuba Pro Air2 etc.) Technician Labor. Parts Not Included.
$20-$35 For Service Parts Kit.
HYDRO & VISUAL INSPECTION SERVICE
DOT requires your Cyclinder be hydrostatic tested every 5 years by an authorized Hydrostatic Testing Facility. The Hydro Testing Process takes 7 Days – Depending on how many cyclinders are sent in by other shops and Paintball Companies. Once the cyclinder passes it's Hydro Test, the cyclinder will receive a current hydro Stamp and Visiual Inspection Sticker.
This Service Takes 10 Business Days.
If you need the cyclinder within 48 hours, a rush service of $20 is available if is dropped off no later then 11AM.
$53 Hydro Test Alumimun or Steel Cylinder's Up To 3500 psi, Includes Visual Inspection and Free Air Fill.
$63 Hydro Test (SCBA) Carbon Fiber Cylinders, Includes Visual Inspection and Air Fill.
$43 Hydro Test Paintball Cylinder's, Includes Visual Inspection and Free Air Fill.
$10 Visual Annual Inspection Only.
$26 Tumble/Cleaning Only.
$25 Cylinder Valve Rebuild, Included Labor, Parts Included.
$3 Viton O-Ring Each.
AIR FILL SERVICE
Proof of Certification Required for all SCUBA Fills
(Current Visual & Hydro Required on ALL Cyclinders)
$7 Air Fill up to 3500 psi.
$15 Air Fill SCBA (Carbon Fiber) Fills up to 4500 psi.
FREE Air Fill Pony Bottles up to 19 cu ft.
FREE Air Fill Top-Off up to 1000 psi.
$20 Nitrox 32% Blend up to 3500 psi.